OpenCV物体跟踪树莓派视觉小车实现过程学习
作者：_睿智_ 发布时间：2021-09-15 21:55:48
标签：OpenCV,树莓派视觉,物体跟踪
物体跟踪效果展示
过程：
一、初始化
def Motor_Init():
global L_Motor, R_Motor
L_Motor= GPIO.PWM(l_motor,100)
R_Motor = GPIO.PWM(r_motor,100)
L_Motor.start(0)
R_Motor.start(0)
def Direction_Init():
GPIO.setup(left_back,GPIO.OUT)
GPIO.setup(left_front,GPIO.OUT)
GPIO.setup(l_motor,GPIO.OUT)
GPIO.setup(right_front,GPIO.OUT)
GPIO.setup(right_back,GPIO.OUT)
GPIO.setup(r_motor,GPIO.OUT)
def Servo_Init():
global pwm_servo
pwm_servo=Adafruit_PCA9685.PCA9685()
def Init():
GPIO.setwarnings(False)
GPIO.setmode(GPIO.BCM)
Direction_Init()
Servo_Init()
Motor_Init()
二、运动控制函数
def Front(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,1) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,1) #right_front
GPIO.output(right_back,0) #right_back
def Back(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,1) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,1) #right_back
def Left(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,1) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,1) #right_front
GPIO.output(right_back,0) #right_back
def Right(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,1) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,1) #right_back
def Stop():
L_Motor.ChangeDutyCycle(0)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(0)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,0) #right_back
三、舵机角度控制
def set_servo_angle(channel,angle):
angle=4096*((angle*11)+500)/20000
pwm_servo.set_pwm_freq(50) #frequency==50Hz (servo)
pwm_servo.set_pwm(channel,0,int(angle))
set_servo_angle(4, 110) #top servo lengthwise
#0:back 180:front
set_servo_angle(5, 90) #bottom servo crosswise
#0:left 180:right
上面的（4）：是顶部的舵机（摄像头上下摆动的那个舵机）
下面的（5）：是底部的舵机（摄像头左右摆动的那个舵机）
四、摄像头&&图像处理
# 1 Image Process
img, contours = Image_Processing()
width, height = 160, 120
camera = cv2.VideoCapture(0)
camera.set(3,width)
camera.set(4,height)
1、打开摄像头
打开摄像头，并设置窗口大小。
设置小窗口的原因： 小窗口实时性比较好。
# Capture the frames
ret, frame = camera.read()
2、把图像转换为灰度图
# to gray
gray = cv2.cvtColor(frame, cv2.COLOR_BGR2GRAY)
cv2.imshow('gray',gray)
3、 高斯滤波（去噪）
# Gausi blur
blur = cv2.GaussianBlur(gray,(5,5),0)
4、亮度增强
#brighten
blur = cv2.convertScaleAbs(blur, None, 1.5, 30)
5、转换为二进制
#to binary
ret,binary = cv2.threshold(blur,150,255,cv2.THRESH_BINARY_INV)
cv2.imshow('binary',binary)
6、闭运算处理
#Close
kernel = cv2.getStructuringElement(cv2.MORPH_RECT, (17,17))
close = cv2.morphologyEx(binary, cv2.MORPH_CLOSE, kernel)
cv2.imshow('close',close)
7、获取轮廓
#get contours
binary_c,contours,hierarchy = cv2.findContours(close, 1, cv2.CHAIN_APPROX_NONE)
cv2.drawContours(image, contours, -1, (255,0,255), 2)
cv2.imshow('image', image)
代码
def Image_Processing():
# Capture the frames
ret, frame = camera.read()
# Crop the image
image = frame
cv2.imshow('frame',frame)
# to gray
gray = cv2.cvtColor(frame, cv2.COLOR_BGR2GRAY)
cv2.imshow('gray',gray)
# Gausi blur
blur = cv2.GaussianBlur(gray,(5,5),0)
#brighten
blur = cv2.convertScaleAbs(blur, None, 1.5, 30)
#to binary
ret,binary = cv2.threshold(blur,150,255,cv2.THRESH_BINARY_INV)
cv2.imshow('binary',binary)
#Close
kernel = cv2.getStructuringElement(cv2.MORPH_RECT, (17,17))
close = cv2.morphologyEx(binary, cv2.MORPH_CLOSE, kernel)
cv2.imshow('close',close)
#get contours
binary_c,contours,hierarchy = cv2.findContours(close, 1, cv2.CHAIN_APPROX_NONE)
cv2.drawContours(image, contours, -1, (255,0,255), 2)
cv2.imshow('image', image)
return frame, contours
五、获取最大轮廓坐标
由于有可能出现多个物体，我们这里只识别最大的物体（深度学习可以搞分类，还没学到这，学到了再做），得到它的坐标。
# 2 get coordinates
x, y = Get_Coord(img, contours)
def Get_Coord(img, contours):
image = img.copy()
try:
contour = max(contours, key=cv2.contourArea)
cv2.drawContours(image, contour, -1, (255,0,255), 2)
cv2.imshow('new_frame', image)
# get coord
M = cv2.moments(contour)
x = int(M['m10']/M['m00'])
y = int(M['m01']/M['m00'])
print(x, y)
return x,y
except:
print 'no objects'
return 0,0
返回最大轮廓的坐标：
六、运动
根据反馈回来的坐标，判断它的位置，进行运动。
# 3 Move
Move(x,y)
1、没有识别到轮廓（静止）
if x==0 and y==0:
Stop()
2、向前走
识别到物体，且在正中央（中间1/2区域），让物体向前走。
#go ahead
elif width/4 <x and x<(width-width/4):
Front(70)
3、向左转
物体在左边1/4区域。
#left
elif x < width/4:
Left(50)
4、向右转
物体在右边1/4区域。
#Right
elif x > (width-width/4):
Right(50)
代码
def Move(x,y):
global second
#stop
if x==0 and y==0:
Stop()
#go ahead
elif width/4 <x and x<(width-width/4):
Front(70)
#left
elif x < width/4:
Left(50)
#Right
elif x > (width-width/4):
Right(50)
总代码
#Object Tracking
import RPi.GPIO as GPIO
import time
import Adafruit_PCA9685
import numpy as np
import cv2
second = 0
width, height = 160, 120
camera = cv2.VideoCapture(0)
camera.set(3,width)
camera.set(4,height)
l_motor = 18
left_front = 22
left_back = 27
r_motor = 23
right_front = 25
right_back = 24
def Motor_Init():
global L_Motor, R_Motor
L_Motor= GPIO.PWM(l_motor,100)
R_Motor = GPIO.PWM(r_motor,100)
L_Motor.start(0)
R_Motor.start(0)
def Direction_Init():
GPIO.setup(left_back,GPIO.OUT)
GPIO.setup(left_front,GPIO.OUT)
GPIO.setup(l_motor,GPIO.OUT)
GPIO.setup(right_front,GPIO.OUT)
GPIO.setup(right_back,GPIO.OUT)
GPIO.setup(r_motor,GPIO.OUT)
def Servo_Init():
global pwm_servo
pwm_servo=Adafruit_PCA9685.PCA9685()
def Init():
GPIO.setwarnings(False)
GPIO.setmode(GPIO.BCM)
Direction_Init()
Servo_Init()
Motor_Init()
def Front(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,1) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,1) #right_front
GPIO.output(right_back,0) #right_back
def Back(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,1) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,1) #right_back
def Left(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,1) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,1) #right_front
GPIO.output(right_back,0) #right_back
def Right(speed):
L_Motor.ChangeDutyCycle(speed)
GPIO.output(left_front,1) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(speed)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,1) #right_back
def Stop():
L_Motor.ChangeDutyCycle(0)
GPIO.output(left_front,0) #left_front
GPIO.output(left_back,0) #left_back
R_Motor.ChangeDutyCycle(0)
GPIO.output(right_front,0) #right_front
GPIO.output(right_back,0) #right_back
def set_servo_angle(channel,angle):
angle=4096*((angle*11)+500)/20000
pwm_servo.set_pwm_freq(50) #frequency==50Hz (servo)
pwm_servo.set_pwm(channel,0,int(angle))
def Image_Processing():
# Capture the frames
ret, frame = camera.read()
# Crop the image
image = frame
cv2.imshow('frame',frame)
# to gray
gray = cv2.cvtColor(frame, cv2.COLOR_BGR2GRAY)
cv2.imshow('gray',gray)
# Gausi blur
blur = cv2.GaussianBlur(gray,(5,5),0)
#brighten
blur = cv2.convertScaleAbs(blur, None, 1.5, 30)
#to binary
ret,binary = cv2.threshold(blur,150,255,cv2.THRESH_BINARY_INV)
cv2.imshow('binary',binary)
#Close
kernel = cv2.getStructuringElement(cv2.MORPH_RECT, (17,17))
close = cv2.morphologyEx(binary, cv2.MORPH_CLOSE, kernel)
cv2.imshow('close',close)
#get contours
binary_c,contours,hierarchy = cv2.findContours(close, 1, cv2.CHAIN_APPROX_NONE)
cv2.drawContours(image, contours, -1, (255,0,255), 2)
cv2.imshow('image', image)
return frame, contours
def Get_Coord(img, contours):
image = img.copy()
try:
contour = max(contours, key=cv2.contourArea)
cv2.drawContours(image, contour, -1, (255,0,255), 2)
cv2.imshow('new_frame', image)
# get coord
M = cv2.moments(contour)
x = int(M['m10']/M['m00'])
y = int(M['m01']/M['m00'])
print(x, y)
return x,y
except:
print 'no objects'
return 0,0
def Move(x,y):
global second
#stop
if x==0 and y==0:
Stop()
#go ahead
elif width/4 <x and x<(width-width/4):
Front(70)
#left
elif x < width/4:
Left(50)
#Right
elif x > (width-width/4):
Right(50)
if __name__ == '__main__':
Init()
set_servo_angle(4, 110) #top servo lengthwise
#0:back 180:front
set_servo_angle(5, 90) #bottom servo crosswise
#0:left 180:right
while 1:
# 1 Image Process
img, contours = Image_Processing()
# 2 get coordinates
x, y = Get_Coord(img, contours)
# 3 Move
Move(x,y)
# must include this codes(otherwise you can't open camera successfully)
if cv2.waitKey(1) & 0xFF == ord('q'):
Stop()
GPIO.cleanup()
break
#Front(50)
#Back(50)
#$Left(50)
#Right(50)
#time.sleep(1)
#Stop()
检测原理是基于最大轮廓的检测，没有用深度学习的分类，所以容易受到干扰，后期学完深度学习会继续优化。有意见或者想法的朋友欢迎交流。
来源：https://blog.csdn.net/great_yzl/article/details/120338859
0
投稿猜你喜欢
1. 在Python中使用中文在Python中有两种默认的字符串：str和- 1、列表页面：this.$router.push({ name: 'userTemplate', params: { rep
- 使用环境在cmd模式下输入 mysql --version (查看mysql安装的版本).完整的命令可以通过mysql --help来获取.
- xpath表达式1. xpath语法<bookstore><book> <title lang="e
- 1. Mysql备份某个数据库的命令####################################################
- 网页过渡是指当浏览者进入或离开网页时，页面呈现的不同的刷新效果，比如卷动、百叶窗等。注：通过模板所建网页无法添加网页过渡效果！制作步骤：1、
- 创建一个表T_Employee并插入若干数据 代码如下:create table T_Employee(FNumber VARC
- Golang中的time.After的使用理解关于在goroutine中使用time.After的理解， 新手在学习过程中的“此时此刻”的理
- 进入python的安装目录, 查看python解释器进入bin目录 # ls python(看一下是否有python解释器版本) # pwd
- 前言编写函数或者类时，还可以为其编写测试。通过测试，可确定代码面对各种输入都能够按要求的那样工作。本次我将介绍如何使用Python模块uni
- 概要介绍mmpi，是一款使用python实现的开源邮件快速检测工具库，基于community框架设计开发。mmpi支持对邮件头、邮件正文、邮
- apache对php的支持是通过apache的mod_php5模块来支持的，这点与nginx不同。nginx是通过第三方的fastcgi处理
- 目录主页分析代码：修改视图函数返回值修改 URL 规则修改视图函数名总结追溯到最初，Flask 诞生于 Armin Ronacher 在 2
- form表单中经常涉及复选框（checkbox）和单选框（radiobox），如用户的爱好跑步、游泳、跳舞可以使用复选框，性别男、女可以使用
- 起步Python3 起，str 就采用了 Unicode 编码（注意这里并不是 utf8 编码，尽管 .py 文件默认编码是 utf8 ）。
- 业务说明：此示例脚本作用，包含方法和逻辑：图像读取，图片尺寸读取，重置图片大小，图片等比缩放，图片拼接，图片覆盖与堆叠（子母图）图片展示：单
- 目录简述:1. 事务的四大特性2.多事务并发带来的问题3.事务的隔离级别4.演示不同隔离级别出现的问题读未提交读已提交可重复读串行化5.锁机
- 数据准备ON DUPLICATE KEY UPDATEinsert into test_table(id,username)VALUES(4
- TihuanWords.txt文档格式注意：同一行的词用单个空格隔开，每行第一个词为同行词的替换词。年休假 年假 年休究竟 到底回家场景 我
- 1、将python打包好的exe解压为py文件，步骤如下： 下载pyinstxtractor.py文件2、下载地址：https://nchc
